File manager - Edit - /home/veronikagstoette/public_html/rdma.zip
Back
PK 6H#]��e+ + modules/infiniband.confnu �[��� # These modules are loaded by the system if any InfiniBand device is installed # InfiniBand over IP netdevice ib_ipoib # Access to fabric management SMPs and GMPs from userspace. ib_umad # SCSI Remote Protocol target support # ib_srpt # ib_ucm provides the obsolete /dev/infiniband/ucm0 # ib_ucm PK 6H#] 4�J J modules/iwarp.confnu �[��� # These modules are loaded by the system if any iWarp device is installed PK 6H#]^�s� � modules/opa.confnu �[��� # These modules are loaded by the system if any OmniPath Architecture device # is installed # Infiniband over IP netdevice ib_ipoib # Access to fabric management SMPs and GMPs from userspace. ib_umad # Omnipath Ethernet Virtual NIC netdevice opa_vnic PK 6H#]��xV� � modules/rdma.confnu �[��� # These modules are loaded by the system if any RDMA devices is installed # iSCSI over RDMA client support ib_iser # iSCSI over RDMA target support ib_isert # SCSI RDMA Protocol target driver ib_srpt # User access to RDMA verbs (supports libibverbs) ib_uverbs # User access to RDMA connection management (supports librdmacm) rdma_ucm # RDS over RDMA support # rds_rdma # NFS over RDMA client support xprtrdma # NFS over RDMA server support svcrdma PK 6H#]�q�c c modules/roce.confnu �[��� # These modules are loaded by the system if any RDMA over Converged Ethernet # device is installed PK 6H#]��«� � mlx4.confnu �[��� # Config file for mlx4 hardware port settings # This file is read when the mlx4_core module is loaded and used to # set the port types for any hardware found. If a card is not listed # in this file, then its port types are left alone. # # Format: # <pci_device_of_card> <port1_type> [port2_type] # # @port1 and @port2: # One of auto, ib, or eth. No checking is performed to make sure that # combinations are valid. Invalid inputs will result in the driver # not setting the port to the type requested. port1 is required at # all times, port2 is required for dual port cards. # # Example: # 0000:0b:00.0 eth eth # # You can find the right pci device to use for any given card by loading # the mlx4_core module, then going to /sys/bus/pci/drivers/mlx4_core and # seeing what possible PCI devices are listed there. The possible values # for ports are: ib, eth, and auto. However, not all cards support all # types, so if you get messages from the kernel that your selected port # type isn't supported, there's nothing this script can do about it. Also, # some cards don't support using different types on the two ports (aka, # both ports must be either eth or ib). Again, we can't set what the kernel # or hardware won't support. # PK 6H#]��e+ + modules/infiniband.confnu �[��� PK 6H#] 4�J J r modules/iwarp.confnu �[��� PK 6H#]^�s� � � modules/opa.confnu �[��� PK 6H#]��xV� � ; modules/rdma.confnu �[��� PK 6H#]�q�c c C modules/roce.confnu �[��� PK 6H#]��«� � � mlx4.confnu �[��� PK � �
| ver. 1.4 |
Github
|
.
| PHP 8.2.30 | Generation time: 0 |
proxy
|
phpinfo
|
Settings